- 您现在的位置：买卖IC网 > Sheet目录310 > AL8807W5-7 (Diodes Inc)IC LED DRVR DCDC BUCK SOT25
AL8807
Application Information (cont.)
Diode Selection
For maximum efficiency and performance, the rectifier (D1) should be a fast low capacitance Schottky diode with low reverse leakage at the
maximum operating voltage and temperature. The Schottky diode also provides better efficiency than silicon PN diodes, due to a combination of
lower forward voltage and reduced recovery time.
It is important to select parts with a peak current rating above the peak coil current and a continuous current rating higher than the maximum output
load current. In particular, it is recommended to have a diode voltage rating at least 15% higher than the operating voltage to ensure safe operation
during the switching and a current rating at least 10% higher than the average diode current. The power rating is verified by calculating the power
loss through the diode.
Schottky diodes, e.g. B240 or B140, with their low forward voltage drop and fast reverse recovery, are the ideal choice for AL8807 applications.
Inductor Selection
Recommended inductor values for the AL8807 are in the range 33 μ H to 100 μ H.
Higher values of inductance are recommended at higher supply voltages in order to minimize errors due to switching delays, which result in
increased ripple and lower efficiency. Higher values of inductance also result in a smaller change in output current over the supply voltage range.
(See graphs).
Figure 34 Inductor value with input voltage and number of LEDs
The inductor should be mounted as close to the device as possible with low resistance/stray inductance connections to the SW pin.
The chosen coil should have a saturation current higher than the peak output current and a continuous current rating above the required mean
output current.
Suitable coils for use with the AL8807 are listed in the table below:
Part No.
MSS1038-333
MSS1038-683
NPIS64D330MTRF
L
(μH)
33
68
33
DCR
(V)
0.093
0.213
0.124
I SAT
(A)
2.3
1.5
1.1
Manufacturer
CoilCraft www.coilcraft.com
NIC www.niccomp.com
The inductor value should be chosen to maintain operating duty cycle and switch 'on'/'off' times over the supply voltage and load current range.
AL8807
Document number: DS35281 Rev. 5 - 2
12 of 20
www.diodes.com
March 2013
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AL9910AS-13
IC LED DRVR HIGH BRIGHT SO8EP
ALC60481R05
PWR SUP AC-DC 6-48V 1.05A 50.4W
ALV100362R5
POWER SUPPLY AC-DC 36V 2.5A 90W
ALV60361R7
POWER SUPPLY AC-DC 36V 1.7A 61W
ALV80126R5
POWER SUPPLY AC-DC 12V 6.5A 78W
AOZ1083CI
IC LED DRVR BUCK CC 1.2A SOT23-6
AOZ1935QI
IC LED DRVR WHITE BCKLGT 16QFN
AOZ1977AI
IC LED DRVR BCKLGT 16SOIC
相关代理商/技术参数
AL8808EV1
功能描述:AL8808 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:6 V ~ 30 V 所含物品:板 使用的 IC/零件:AL8808 标准包装:1
AL8808EV2
功能描述:AL8808 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:12VAC，12 V ~ 20 V 所含物品:板 使用的 IC/零件:AL8808 标准包装:1
AL8808WT-7
功能描述:LED照明驱动器 LED MV Int Switch TS Switch TSOT25 T&R 3K
RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
AL8811
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Boost/Buck/Inverting DC-DC CONVERTER
AL8811M8-13
制造商:Diodes Incorporated 功能描述:LED LV INT SWITCH MSOP-8 T&R 2.5K - Tape and Reel 制造商:Diodes Incorporated 功能描述:LED MV INT SWITCH MSOP-8
AL8812FDF-13
功能描述:LED LV INT SWITCH U-DFN6040-12 T 制造商:diodes incorporated 系列:* 零件状态:有效 标准包装:3,000
AL8820MPTR-G1
功能描述:IC LED DRIVER OFFLINE 8MSOP 制造商:diodes incorporated 系列:* 零件状态:过期 标准包装:2,500
AL8820SP-13
功能描述:LED 驱动器 IC 1 输出 交直流离线开关 降压（降压），升压（升压） 2A 8-SO 裸露焊盘 制造商:diodes incorporated 系列:- 包装:剪切带（CT） 零件状态:有效 类型:交直流离线开关 拓扑:降压（降压），升压（升压） 内部开关:是 输出数:1 电压 - 供电（最低）:5V 电压 -?供电（最高）:36V 电压 - 输出:40V 电流 - 输出/通道:2A 频率:1MHz 调光:- 应用:- 工作温度:-40°C ~ 105°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽）裸焊盘 供应商器件封装:8-SO 裸露焊盘 标准包装:1